Crayon Wallet Tutorial

This adorable crayon wallet will be a lifesaver when you need to keep your kiddo busy while you’re out and about.

One special feature of this crayon wallet (and the reason I almost named this “The Anal Mommy’s Crayon Wallet Tutorial”) is that the crayon slots stick out only on the inside of the wallet, and not out the back… a tad bit more work, but so much more attractive!

The tutorial is for a two-panel or three-panel crayon wallet and incorporates a detachable strap, as well as several closure options (I prefer snaps, but buttons or Velcro work great, too).

This tutorial is an easy-to-follow, detailed 11-page pdf file including color photos and guides for marking the material.  It is available in Letter size (for North America) or A4 size (for the rest of the world), to assure that the pattern and guide dimensions print accurately.

Order your the PDF tutorial here:  AngieBartosDesigns

Crayon Wallet © 2010 Angela Bartos. All rights reserved.
No portion of this pattern may be reproduced
without expressed written permission by the author.

The Awesome All-in-One Bag

I had gotten tired of lugging around a bag for diapers and sippy cups and another one for my own items.  I decided I needed a roomy bag with lots of pockets.  So here it is...

First of all, I'm using a sturdy canvas fabric (from IKEA) so that I don't need to bother with interfacing to strengthen the material.  I suggest reading through the entire tutorial before getting started.

Print out the pattern, piecing it together matching up the labeled cross-hairs (pattern pages will slightly overlap).  Place the pattern on the fold of your fabric and cut one piece from your outer fabric and one piece from a coordinating liner fabric.  You'll also need a rectangle for the inner pockets measuring about 30" x 8".  And you'll need a strip measuring 8" x 2" for the closure ribbon.

 

Now to prepare the pockets... If you have a serger, serge the long edge of the pocket piece that you would like to become the top of the pocket, then fold the edge in about an inch and press. If you don't have access to a serger, just fold the edge over twice to enclose the raw edge.  Then topstitch to hold the edge in place.

Now take your liner fabric and mark a line on the right side about 3 inches from the base (the mark will be covered by the pocket).

 

Then line up the long, raw edge of the pocket along the underside of the line, with right sides together.  I'm pretty sure that'll only make sense after looking at the photo below. 

Pin and sew about 1/4 inch from the edge of the raw pocket edge.

Then fold the pocket up against the liner fabric and press along the fold.  Then topstitch just over 1/4 inch from the fold, to enclose that raw edge.

Now your liner fabric should look like this:

Use chalk to mark lines where you would like pockets.  (I usually make about four or five large pockets and one narrow pocket to hold a pen or pencil.)

Now fold the liner piece in half with right sides facing each other.  Sew the side seam with about 1/2" seam allowance.  Repeat for the outer piece.  Now fold the pieces as in the picture below and press the seams open.

Now sew the bottom of the outer fabric, leaving a 1/2" seam allowance.  When you sew the bottom of the liner fabric, leave a large hole for turning the bag later.

Open the corners of the outer fabric and press flat.

Mark a line perpendicular to the bottom seam about 1.5" away from the corner. Repeat for the other corner.

Sew along the line at both corners.

Trim.

Repeat for the corners of the liner.

Now to prepare the closure strap... press the material in half lengthwise, wrong sides together.  Turn in the raw edges to the fold and press closed.  Top stitch along the edges.  (For more specific directions and photos of the making of the strap, see the strap-making portion of my "Nothing-to-it Tote" tutorial.)

Pin the strap to the right side of the outer fabric, at the back seam, as seen below.

Turn the liner right-side out.

Place the liner fabric inside the outer fabric, so that right sides are together.

Line up and pin the inner and outer fabric.  Sew all around the edge, reinforcing over the closure strap.

Clip around all curves and trim strap corners.

Turn right-side out through the whole in the lining, and stuff the lining into the outer fabric.  Press.

Stuff the liner into the outer fabric and press.

 Topstitch around the edge and tie the straps together.

 Attach a big funky button, hand-sew the opening in the liner closed and you're done!!

Enjoy!

Hopefully I'll have time to post a tutorial for the matching diaper case soon!

Paintbrush Roll

One of the neighbor girls, who also babysits the kids from time to time, recently turned 18.  She's studying art in school, so I decided to make her a paintbrush roll to match the bag that I made her for Christmas.  (A tutorial for that coming soon!)  This is so simple, but makes a great gift for the artist in your life.

To get started, cut out your fabric.  I'll let you know what I used, but you can tweak these measurements to fit the brushes, pens, or colored pencils that you're wanting to tote around.  You'll need a piece of outer fabric (mine is the blue patterned fabric below), a piece of inner fabric, and three pieces of fabric for the three layers of pockets.  In addition, you'll need ribbon to tie it closed (or you can make a ribbon from your fabric).

My measurements were:

Outer Fabric:  20" x 13"
Inner Fabric:  20" x 13"
Long Pocket:  8" x 13"
Medium Pocket:  6" x 13"
Short Pocket:  4" x 13"
Ribbon: about 24" long

Fold down the top edge of each pocket piece about an inch and press.  Then fold the raw edge in, and press again.  Top-stitch in place.  If you have a fancy stitch option on your machine, you can spice up your top-stitch that way.

Note: You might be tempted, as I was, to cut your fabric twice as long and just fold it in half to make for a smoother look, but you end up with twice as many layers at the bottom of your project, which makes it hard to roll.

Now lay the pockets in place on the inner fabric piece and mark a line down the center with chalk.  Mark out from the center where you would like to sew pockets.  I made even-width pockets of 1.5 inches, but you can make wider and narrower pockets, depending on what you're planning to stow in them.

Now pin the sides and between some of the pockets to hold it in place while sewing.  Sew along each mark, reinforcing at the tops of each pocket.

Now it's time to layer your fabrics to sew them all together.

First comes your inner fabric with the pockets attached.

Next, place your ribbon, folded in half, with the fold hanging off the edge, and the open ends toward the inside of the project (you'll probably need to fold the ribbon over to assure that it doesn't get too close to the edge of the fabric, where you're about to sew 1/2 inch from the edge).

Now place the outer fabric on top, right side facing down.  Stitch, leaving a space at the top to turn the project inside-out.  Trim your corners before you turn it inside out.

Now press it well and top-stitch around the entire project.

Fill it up with your paintbrushes and whatnot... and roll 'er up...

Done!

Nothing-to-it Tote

This matching tote and crayon roll make a great gift with crayons and a few coloring books.  I made this set for a benefit for the local kindergarten.  This one is just the right size for coloring books, but you can make it any size you want.  (Tutorial for the crayon roll is on my to-do list.)

 

First, let's figure out how large to cut your fabric... decide how high, wide and deep you want your finished bag to be.  I used two styles of fabric... I'll call them fabric A (orange) and fabric B (burgundy).

 

If you just want to make yours the same size as mine... perfect for standard coloring books or magazines, then just skip past all the math and see my fabric dimensions.  If you'd like to make yours custom-sized... here's the fun algebra:

Let's say:

x = desired height of bag  (mine is 12")
y = desired width of bag  (mine is 9")
z = desired depth of bag  (mine is 2")
µ = desired height of the bag base  (mine is 3")

Fabric A:
cut two:  { x - µ + 1 } by { y + z + 1 }
cut two:  5" by 22"  (for the strap... adjust as desired)

Fabric B:
cut one:  { z + 2 µ + 1 } by { y + z + 1 }
cut one:  { 2 x + z + 1 } by { y + z + 1 }

Interfacing (preferably fusible):

cut one:  { 2 x + z + 1 } by { y + z + 1 }

So since I want my bag to be 12" x 9" x 2" with a 3" base, I will cut the following:

Fabric A: cut two 10" x 12", and cut two 5" x 22"

Fabric B: cut one 9" x 12", and cut one 27" x 12"

Interfacing: cut one 27" x 12"

Leaving a 1/2" seam allowance, sew the three smaller pieces together, like so...

Grab your iron and fuse the interfacing to the back side of this piece.

 

Now fold in half, right sides together, being careful to match seams.  Sew along the sides, leaving a 1/2" seam allowance.  Repeat with the liner fabric, leaving a hole unsewn on one side to turn the tote right-side out later.

Flatten the bottom corner as shown, and mark about { z ÷ 2 } from the corner... for me it was about 1" from the corner, making the length of my mark (and therefore the depth of my bag) 2".

Now sew along that mark and trim.  Repeat for the other corner, as well as the two bottom corners of the lining.

 

Now set all that aside and let's prepare the straps.  Fold the strap pieces lengthwise in half and press.  

 

Then fold the raw ends into the center fold and press.

Now topstitch on both sides.  If you set your needle to the rightmost position, it is easy to stitch close to the edge.

 

On the wrong side of the tote, mark where you would like to have your straps (measure from the seam... I placed mine 3" from the side seam).  Then, with the bag still inside-out, pin the straps in place inside the bag.

Turn your lining fabric right-side out.

Now place it inside the bag and pin in place.  The right sides of the fabric will be facing each other with the straps in between.  Sew around the top of the bag, backstitching over each strap to reinforce.

Turn the bag right-side out through the hole you left, and stitch up the hole by hand.  Then stuff the lining into the bag and press.

Top stitch around the top edge of the bag and you're done!!

If you make a tote using this tutorial, please send me a picture!!  My e-mail is { angie at andrisangie dot com }.  Then go out and enjoy your new bag!!